[root@hpe-xl220agen8v2-01 udisks2]# smartctl -a /dev/sda
smartctl 7.4 2023-08-01 r5530 [x86_64-linux-6.12.0-55.el10.x86_64] (local build)
Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org=== START OF INFORMATION SECTION ===
Device Model:     MM0500GBKAK
Serial Number:    9XF3MPCL
LU WWN Device Id: 5 000c50 07b391c63
Firmware Version: HPGE
User Capacity:    500,107,862,016 bytes [500 GB]
Sector Size:      512 bytes logical/physical
Rotation Rate:    7200 rpm
Form Factor:      2.5 inches
Device is:        Not in smartctl database 7.3/5610
ATA Version is:   ATA8-ACS T13/1699-D revision 6
SATA Version is:  SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is:    Tue Feb 25 01:27:52 2025 EST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSEDGeneral SMART Values:
Offline data collection status:  (0x82)    Offline data collection activity
                    was completed without error.
                    Auto Offline Data Collection: Enabled.
Self-test execution status:      (   0)    The previous self-test routine completed
                    without error or no self-test has ever 
                    been run.
Total time to complete Offline 
data collection:         (  642) seconds.
Offline data collection
capabilities:              (0x7b) SMART execute Offline immediate.
                    Auto Offline data collection on/off support.
                    Suspend Offline collection upon new
                    command.
                    Offline surface scan supported.
                    Self-test supported.
                    Conveyance Self-test supported.
                    Selective Self-test supported.
SMART capabilities:            (0x0003)    Saves SMART data before entering
                    power-saving mode.
                    Supports SMART auto save timer.
Error logging capability:        (0x01)    Error logging supported.
                    General Purpose Logging supported.
Short self-test routine 
recommended polling time:      (   2) minutes.
Extended self-test routine
recommended polling time:      ( 100) minutes.
Conveyance self-test routine
recommended polling time:      (   3) minutes.
SCT capabilities:            (0x103d)    SCT Status supported.
                    SCT Error Recovery Control supported.
                    SCT Feature Control supported.
                    SCT Data Table supported.SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x000f   078   063   044    Pre-fail  Always       -       72679179
  3 Spin_Up_Time            0x0003   096   096   070    Pre-fail  Always       -       0
  4 Start_Stop_Count        0x0032   090   090   020    Old_age   Always       -       10812
  5 Reallocated_Sector_Ct   0x0033   085   085   036    Pre-fail  Always       -       635
  7 Seek_Error_Rate         0x000f   078   060   030    Pre-fail  Always       -       140093027232
  9 Power_On_Hours          0x0032   023   023   000    Old_age   Always       -       67987
 10 Spin_Retry_Count        0x0013   100   100   097    Pre-fail  Always       -       0
 12 Power_Cycle_Count       0x0032   090   090   020    Old_age   Always       -       10810
180 Unknown_HDD_Attribute   0x003b   100   100   030    Pre-fail  Always       -       136454620
184 End-to-End_Error        0x0032   100   100   003    Old_age   Always       -       0
187 Reported_Uncorrect      0x0032   086   086   000    Old_age   Always       -       14
188 Command_Timeout         0x0032   100   097   000    Old_age   Always       -       12885098509
189 High_Fly_Writes         0x003a   091   091   000    Old_age   Always       -       9
190 Airflow_Temperature_Cel 0x0022   075   058   045    Old_age   Always       -       25 (Min/Max 22/25)
191 G-Sense_Error_Rate      0x0032   100   100   000    Old_age   Always       -       0
192 Power-Off_Retract_Count 0x0032   095   095   000    Old_age   Always       -       10809
193 Load_Cycle_Count        0x0032   094   094   000    Old_age   Always       -       12057
194 Temperature_Celsius     0x0022   025   042   000    Old_age   Always       -       25 (0 14 0 0 0)
195 Hardware_ECC_Recovered  0x001a   114   099   000    Old_age   Always       -       72679179
196 Reallocated_Event_Count 0x0033   085   085   036    Pre-fail  Always       -       635
197 Current_Pending_Sector  0x0012   100   091   000    Old_age   Always       -       0
198 Offline_Uncorrectable   0x0010   100   100   000    Old_age   Offline      -       0
199 UDMA_CRC_Error_Count    0x003e   200   200   000    Old_age   Always       -       0SMART Error Log Version: 1
ATA Error Count: 30 (device log contains only the most recent five errors)
    CR = Command Register [HEX]
    FR = Features Register [HEX]
    SC = Sector Count Register [HEX]
    SN = Sector Number Register [HEX]
    CL = Cylinder Low Register [HEX]
    CH = Cylinder High Register [HEX]
    DH = Device/Head Register [HEX]
    DC = Device Command Register [HEX]
    ER = Error register [HEX]
    ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.Error 30 occurred at disk power-on lifetime: 1548 hours (64 days + 12 hours)
  When the command that caused the error occurred, the device was active or idle.  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 00 ff ff ff 0f  Error: UNC at LBA = 0x0fffffff = 268435455  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  60 00 20 ff ff ff 4f 00      02:02:42.088  READ FPDMA QUEUED
  60 00 20 ff ff ff 4f 00      02:02:42.081  READ FPDMA QUEUED
  60 00 08 ff ff ff 4f 00      02:02:42.080  READ FPDMA QUEUED
  60 00 01 ff ff ff 4f 00      02:02:42.044  READ FPDMA QUEUED
  2f 00 01 10 00 00 00 00      02:02:41.922  READ LOG EXTError 29 occurred at disk power-on lifetime: 1548 hours (64 days + 12 hours)
  When the command that caused the error occurred, the device was active or idle.  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 00 ff ff ff 0f  Error: UNC at LBA = 0x0fffffff = 268435455  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  60 00 20 ff ff ff 4f 00      02:02:39.479  READ FPDMA QUEUED
  60 00 20 ff ff ff 4f 00      02:02:39.479  READ FPDMA QUEUED
  60 00 20 ff ff ff 4f 00      02:02:39.478  READ FPDMA QUEUED
  60 00 20 ff ff ff 4f 00      02:02:39.478  READ FPDMA QUEUED
  60 00 20 ff ff ff 4f 00      02:02:39.478  READ FPDMA QUEUEDError 28 occurred at disk power-on lifetime: 744 hours (31 days + 0 hours)
  When the command that caused the error occurred, the device was active or idle.  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 00 ff ff ff 0f  Error: UNC at LBA = 0x0fffffff = 268435455  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  60 00 08 ff ff ff 4f 00      00:05:04.605  READ FPDMA QUEUED
  2f 00 01 10 00 00 00 00      00:05:04.602  READ LOG EXT
  60 00 20 ff ff ff 4f 00      00:05:02.179  READ FPDMA QUEUED
  60 00 20 ff ff ff 4f 00      00:05:02.178  READ FPDMA QUEUED
  60 00 08 ff ff ff 4f 00      00:05:02.178  READ FPDMA QUEUEDError 27 occurred at disk power-on lifetime: 744 hours (31 days + 0 hours)
  When the command that caused the error occurred, the device was active or idle.  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 00 ff ff ff 0f  Error: UNC at LBA = 0x0fffffff = 268435455  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  60 00 20 ff ff ff 4f 00      00:05:02.179  READ FPDMA QUEUED
  60 00 20 ff ff ff 4f 00      00:05:02.178  READ FPDMA QUEUED
  60 00 08 ff ff ff 4f 00      00:05:02.178  READ FPDMA QUEUED
  60 00 08 ff ff ff 4f 00      00:05:02.178  READ FPDMA QUEUED
  60 00 01 ff ff ff 4f 00      00:05:02.178  READ FPDMA QUEUEDError 26 occurred at disk power-on lifetime: 64549 hours (2689 days + 13 hours)
  When the command that caused the error occurred, the device was active or idle.  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 00 ff ff ff 0f  Error: UNC at LBA = 0x0fffffff = 268435455  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  60 00 01 ff ff ff 4f 00      00:06:17.282  READ FPDMA QUEUED
  60 00 01 ff ff ff 4f 00      00:06:17.282  READ FPDMA QUEUED
  60 00 01 ff ff ff 4f 00      00:06:17.282  READ FPDMA QUEUED
  60 00 01 ff ff ff 4f 00      00:06:17.282  READ FPDMA QUEUED
  60 00 01 ff ff ff 4f 00      00:06:17.266  READ FPDMA QUEUEDSMART Self-test log structure revision number 1
Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error
# 1  Short offline       Completed without error       00%      2450         -
# 2  Extended offline    Aborted by host               90%      2447         -
# 3  Conveyance offline  Aborted by host               30%      2447         -
# 4  Short offline       Completed without error       00%      2447         -
# 5  Short offline       Completed without error       00%         6         -
# 6  Short offline       Completed without error       00%         3         -
# 7  Short offline       Completed without error       00%         2         -SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.The above only provides legacy SMART information - try 'smartctl -x' for more[root@hpe-xl220agen8v2-01 udisks2]# 

[root@hpe-xl220agen8v2-01 udisks2]# uname -a
Linux hpe-xl220agen8v2-01.khw.eng.rdu2.dc.redhat.com 6.12.0-55.el10.x86_64 #1 SMP PREEMPT_DYNAMIC Mon Feb 17 05:00:34 EST 2025 x86_64 GNU/Linux
[root@hpe-xl220agen8v2-01 udisks2]# rpm -qa |grep udisks
libudisks2-2.10.90-5.el10.x86_64
udisks2-2.10.90-5.el10.x86_64
udisks2-iscsi-2.10.90-5.el10.x86_64
udisks2-lsm-2.10.90-5.el10.x86_64
udisks2-lvm2-2.10.90-5.el10.x86_64
udisks2-debugsource-2.10.90-5.el10.x86_64
udisks2-debuginfo-2.10.90-5.el10.x86_64
libudisks2-debuginfo-2.10.90-5.el10.x86_64
udisks2-iscsi-debuginfo-2.10.90-5.el10.x86_64
udisks2-lsm-debuginfo-2.10.90-5.el10.x86_64
udisks2-lvm2-debuginfo-2.10.90-5.el10.x86_64
libudisks2-devel-2.10.90-5.el10.x86_64
[root@hpe-xl220agen8v2-01 udisks2]# 



======================================================================
FAIL: test_sda (__main__.Smart.test_sda)
SMART status of first internal hard disk
----------------------------------------------------------------------
Traceback (most recent call last):
  File "/var/roothome/rpmbuild/BUILD/udisks-2.10.90/src/tests/integration-test", line 1328, in test_sda
    self.assertEqual(ata.get_property('smart-failing'), False)
AssertionError: True != False

----------------------------------------------------------------------
Ran 31 tests in 256.571s

FAILED (failures=1)